
1-10 | 24 |
10-20 | 23 |
>20 | 22 |
3.7V Inductor Capacitor ESR Meter Transistor Tester DIY MG328 Multifunction Tester
Product parameter:
Instrument power supply: 3.7V power supply or direct power supply via micro USB interface
◆Using ATmega328 microcontroller.
◆12864 graphic LCD display test results.
◆One-key operation automatically turns off the power.
◆Exclusively increase the power switch to avoid battery consumption during storage and shutdown.
◆Automatically detect PNP and NPN bipolar transistors, N and P channel MOSFETs, JFET field-effect transistors, diodes, double diodes, SCRs, resistors, capacitors, and inductors. Automatically detect pin definitions.
◆Measure the current amplification factor (B) of the bipolar transistor and the conduction voltage (Uf) of the emitter junction. Darlington transistors can be identified by high threshold voltage and high current amplification factors.
◆The protection diodes inside bipolar transistors and MOSFETs can be detected and displayed on the screen.
◆Measure the threshold voltage and gate capacitance of MOSFET.
◆Support the measurement of two resistances, and the potentiometer can also be measured. If the potentiometer is adjusted to one end of it, the tester cannot distinguish the pins in the middle and both ends.
◆The resolution of resistance measurement is 0.1 ohm, and the highest measurement value is 50M ohm.
◆The capacitance measurement range is from 25pf to 100mF (100,000 UF). The resolution can reach 1 pF, and the inductance measurement range is 0.01MH-20H, otherwise, it will be displayed as a resistance. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as resistance.
◆It can detect the equivalent series resistance (ESR) of capacitors above 2UF with a resolution of 0.01 ohm. This function is very important for detecting capacitance performance.
◆It can display the symbol of the correct direction for two diodes, and display the forward voltage drop at the same time.
◆The LED is detected as a diode, and the forward voltage drop is higher than the normal value. The dual light-emitting diodes are detected as dual diodes. The light-emitting diode will flash during detection.
◆The time for each test is about two seconds, only the large capacitance and inductance measurement will take a long time.
Correction method:
Short connect the three test terminals and enter the test. The screen prompts the calibration steps.
1. When prompted to disconnect the short connect, disconnect the three test terminals and the calibration will continue;
2. When prompted to connect a capacitor of more than 100nF to pins 1-3, please connect a non-polarized capacitor of more than 100nF, and the program will automatically enter the next step. Until the end of the correction to restart, can complete the correction.
Note: When installing the battery for the first time, you need to activate the battery.
Method 1: After installing the battery, use tweezers or a short wire to short the two holes.
Method 2: After installing the battery, plug in the charger to complete the activation.
Payment method:
How to determine product prices and shipping costs?When you are ready to buy one or more products. You can consult the sales Manager to get a sample of the proforma invoice. The category, product price, and freight are included. |
||
How to complete the payment?We have the following payment methods. You can tell our sales Manager which payment you prefer and complete it. After the customer service checks and confirms the payment is completed. Provide the proforma invoice. And we will prepare to ship. |
||
Cryptocurrency Payment |
||
![]() |
The payment method at the designated address is efficient and practical and can be used anywhere in the world. Wallet Address |
|
![]() |
The payment method at the designated address is efficient and practical and can be used anywhere in the world. |
|
![]() |
||
Bank Transfer |
Other payment methods |
|
![]() |
Wire transfer [Hong Kong] Card Number |
![]() |
![]() |
Wire transfer [China Mainland] Card Number |
![]() |
Cooperation express: |
![]() |
Q: When will we ship after payment?
A: In order to ensure that the products we ship are in good condition. Issued approximately 3 days after receiving your payment.
Q: What if the product is damaged during transportation?
A: We will use a more robust package when shipping to avoid damage to the goods, and we can purchase transportation insurance in advance to reduce the loss of in the transport. although this problem is not common.
Q: What payment methods do we support?
A: We support Bank transfer, wire transfer, Western Union, BTC, third party guarantee, letter of credit and Paypal.
Q: What should I do if there is a problem after receiving the products?
A: We have established good relationships with the maintenance departments in many countries around the world. For example Venezuela, Iran, etc. If you have any questions within 3 days of receiving the goods, you can get free repair service.
Q: Which express we support?
A: We will choose one cheapest and fastest transport way for you. and we support DHL, UPS, TNT, Federation, also have special express, such as Russia, the United States, Kuwait, etc.