Aladdin Innosilicon Series Test Fixtures

Aladdin Innosilicon Series Test Fixtures
Aladdin Innosilicon Series Test Fixtures
1 100

MOQ: 1 Weight: 1.5 KG

+ Add To Cart
If you dont know how to place an order please check our FAQs

WhatsApp : +8618623251355
Notice!
Recently, Our customers have reported that someone pretending to be our customer service staff. Please pay attention to the phone number above which is the only WhatsApp of Zeus mining ltd. Any other contact way not on our website was not our responsibility. If you find someone else pretending to us, please email the screenshots to [email protected] immediately and terminate the transaction to avoid loss.
Product description:

Universal Innosilicon & Aladdin Test Fixture / Multifunctional test fixture

Aladdin Innosilicon series test fixtures can test hash boards and digital power supplies without the computer independently. The test fixture supports Innosilicon T1, T2TS, T2TH, T2TZ, T3, A4+, A6, A9, Aladdin L1, L2HF, L2HU, L2SU, L2HL, and other models. The power supply test supports all series of digital power supplies of Innosilicon.

innosilicon test fixture

The test fixture can accurately determine whether the miner's hash board and power supply are faulty without removing the shelf or dismantling the miner. The maintenance mode can accurately locate the cause of the hash board failure, significantly improving the miner's heat maintenance and operation and maintenance efficiency.

Interface description of Aladdin Innosilicon series test fixtures

test fixture interface 

1. Hash board interface;

2. 4Pin power supply and power communication interface;

3. 6Pin fan power supply interface;

4. Mainboard spare power jumper (when testing T1/L1, the test fixture needs to supply power from the fan power supply interface first and then short the jumper; otherwise, it can be kept disconnected);

5. 1*4Pin fan drive interface;

6. 2*4pin or 6Pin fan drive ports;

7. Test fixture reset button;

8. USB communication interface (connect PC serial port at 115200 baud rate, can output detailed test information);

9. Brief test information display screen;

10. Up function button;

11. Down function button;

12. Debug mode function button;

Test model of the Innosilicon & Aladdin Test Fixture

1. Power supply test

(1) Power supply quick test

When testing the digital power supply, insert the 4Pin power cable of the digital power supply into interface 2 of the test fixture, and then turn on the digital power switch to be tested. After waiting for about 8 seconds, you can observe the power supply test information through the test fixture display screen to judge whether the power supply to be tested is normal.

power supply quick test result

Display area content description:

A. "Test Start!!" prompts the test to start;

B. The power communication test has two results, "DP NG!" and "DP OK!"; "NG" means communication is failure, "OK" means communication is normal.

C. "Chain Break!! E0:1-" shows the hash board test results. When measuring power supply, it can be ignored;

D. "DP OUT= 0-" "DP OUT= 1565-" indicates the output power voltage value. Represent output voltage 0V and output voltage 15.65V respectively;

E. "Press RESET Again!" indicates that the test has ended. Please press the reset button 7 of the test fixture to repeat the test.

(2) Power supply depth test

Under normal circumstances, the test fixture will not enter the power supply full process test mode. Only when the UP (11 key) and DOWN (10 key) buttons are pressed and turned on before the power is turned on, the test fixture will enter the power depth test mode. After entering this mode, the MODE key can control the power supply's output voltage, and the 0~31 gear voltage can be manually adjusted through the UP and DOWN buttons.

power supply depth test result 

Display area content description:

A: "Vendor: GP-" indicates the power supply code; (GP means Gaosbao; AR means Anrui; QB means Qianben)

B: "Ver:14.66-" indicates that the firmware version information of the power supply is 14.66;

C: "DP Vset= 1535-7" means the output voltage of the power supply setting to 15.35V in 7th gear;

D: "DP Vout= 1547-" indicates that the power supply outputs 15.47V voltage;

E: "DP Iout=195--" indicates that the actual output current of the current power supply is 1.95A;

F: "Status: PSU ON--" means power output state, ON means open, OFF means close;

G: "Com Error: 0-" indicates the number of errors in power data communication. If it is not 0, there is a communication failure in the power supply, and the control board does not control the power supply.

2. Hash board test

(1) Quick connection test

In this test state, the heat dissipation of the hash board is not so significant, and there is no need to connect the fan power cable and cooling fan.

When the USB serial port is not connected, you can view the test results on display. After the USB serial port is connected, find the correct COM port and open the serial port with a baud rate of 115200 to view the test details.

hashboard quick connection test result 

Display area content description:

A."Chain OK!" means that the hash board is connected successfully.

B. "Chips: 140-" indicates there are 140 chips on the hash board.

C. "Vol Read OK! 454-" means the hash board chip voltage read successfully. And the average voltage of each chip is 454mV.

"TEMP Read OK! 16-" indicates that the hash board chip temperature is read successfully. And the average temperature of each chip is 16 ℃.

D. "Test PASS!" means the hash board test passed.

(2) Full process test

In addition to the mining test, the hash board will generate a lot of heat in this test mode, and the fan power cable and cooling fan must be connected to achieve a good cooling effect.

Under normal circumstances, it will not enter the whole process test mode; only the test fixture is connected to the computer through USB; press and hold the debug mode function key 12 before powering on, and release the following content after the serial port prints the prompt information.

"----Enter Debug Mode!----"

"Please enter the PowerOn VID value (0~31, default 0):"

LED display shows "DEBUG MODE:"

Indicates that the whole process test mode is entered at this time. (Before entering this mode, please ensure that the power interface of the test fixture is connected to the hash board to be tested, and the fan power supply and fan drive port are connected, and then power on for testing)

What are the specific setting steps of the Innosilicon and Aladdin test fixture?

Step 1: Enter PowerOn VID value 

According to the prompt, use the keyboard to set the output voltage of the power supply during the test (between 0 and 31, the default is 0), which is the startup voltage of the hash board. The smaller the input value, the higher the output voltage (12V~16V). If it exceeds the range, you need to re-enter.

Step 2: Please input working PLL frequency MHz of Board 0 (120~1400, default 0)

Use the keyboard to set the running frequency of the hash board during the test (120~1400, default 0) according to the prompts. After entering the value, press Enter to confirm; the power consumption will be larger if the input value is larger.

Step3: Press Enter to set pll

The voltage and temperature information read from the hash board will be displayed before increasing the operating frequency. Press Enter to confirm the frequency increase. If the hash board chain fails, it will enter the maintenance mode and send maintenance instructions to the hash board without interruption. The power supply will not be interrupted, and an oscilloscope will be used to locate the faulty chip.

Step 4: Press Enter to change the vid

After increasing the operating frequency of the hash board to the specified value, if the above prompt appears, the output voltage of the power supply can be automatically changed 5 times, and the voltage change of the hash board chip can be observed for each change.

Step 5: After the test is over, observe the expected output of the test results.

test results for Innosilicon test fixture 

Our Customers and Partners:

We treat our customers and partners as sincere friends and do our best to provide technical support and aftersales service.
Payment method:

How to determine product prices and shipping costs?

When you are ready to buy one or more products. You can consult the sales Manager to get a sample of the proforma invoice. The category, product price, and freight are included.

How to complete the payment?

We have the following payment methods. You can tell our sales Manager which payment you prefer and complete it. After the customer service checks and confirms the payment is completed. Provide the proforma invoice. And we will prepare to ship.

Cryptocurrency Payment

The payment method at the designated address is efficient and practical and can be used anywhere in the world.
Wallet Address
The payment method at the designated address is efficient and practical and can be used anywhere in the world.

Wallet Address

Bank Transfer

Other payment methods

Wire transfer [Hong Kong]
Card Number
Wire transfer [China Mainland]
Card Number

Cooperation express:

Q: When will we ship after payment?
A: In order to ensure that the products we ship are in good condition. Issued approximately 3 days after receiving your payment.

Q: What if the product is damaged during transportation?
A: We will use a more robust package when shipping to avoid damage to the goods, and we can purchase transportation insurance in advance to reduce the loss of in the transport. although this problem is not common.

Q: What payment methods do we support?
A: We support Bank transfer, wire transfer, Western Union, BTC, third party guarantee, letter of credit and Paypal.

Q: What should I do if there is a problem after receiving the products?
A: We have established good relationships with the maintenance departments in many countries around the world. For example Venezuela, Iran, etc. If you have any questions within 3 days of receiving the goods, you can get free repair service.

Q: Which express we support?
A: We will choose one cheapest and fastest transport way for you. and we support DHL, UPS, TNT, Federation, also have special express, such as Russia, the United States, Kuwait, etc.

More FAQs

If you have any questions, please leave us a message.
Leave message



SKCHUAH 2022/7/16 17:25:28
Q:RFQ FOR ASIC IC BM1362AI
A:hello sir, the price of BM1362AI is 38 dollars a piece, how many pieces do you need
Scott 2022/7/9 5:36:19
Q:Do you have Canaan 1246A Control boards?
A:Dear Sir/Madam, please refer to our FAQ place order, or contact our Pre-sale service via WhatsApp. Thank you.
https://www.zeusbtc.com/FAQ.asp
Yves Djiki 2022/7/9 2:12:41
Q:I have an issue with my avalon miner 1166 pro.
can you help me fix it ?
A:Dear Sir/Madam, please refer to our FAQ place order, or contact our Pre-sale service via WhatsApp. Thank you.
https://www.zeusbtc.com/FAQ.asp
Edoardo 2022/5/11 15:09:11
Q:Hello,

how much is the cost for one working DR5 hashboard including shipping to Italy?

Thanks
A:Dear Customer,
We contacted you via e-mail. Please feel free to contact us if needed.
https://www.zeusbtc.com/FAQ.asp
[email protected]
orhan öğüt 2022/5/11 4:19:54
Q:selam ben türkiyede asıc miner tamiratı yapıyorum benimde ismimi yayınlarmısınız
teşekür ederim
A:Sayın Müşteri,
Sizinle e-posta yoluyla iletişime geçtik. Gerekirse lütfen bizimle iletişime geçmekten çekinmeyin.
https://www.zeusbtc.com/FAQ.asp
[email protected]
вы 2022/5/11 2:32:25
Q:вмамв

A:Уважаемый клиент,
Мы связались с вами по электронной почте. Пожалуйста, не стесняйтесь обращаться к нам в случае необходимости.
https://www.zeusbtc.com/FAQ.asp
[email protected]
Sebastian 2022/5/6 22:43:00
Q:Hi, are they compatible with the antiminer S19 line?
A:Dear Customer,
We have contacted you by email. Please feel free to contact us if necessary.
https://www.zeusbtc.com/FAQ.asp
[email protected]
Cesar 2022/5/4 1:30:30
Q:I got an Avalon 841 hashboard with a missing ceramic capacitor, downside says "C2", do you know that capacitor value? Thank you
A:Dear Sir/Madam, please refer to our FAQ place order, or contact our Pre-sale service via WhatsApp or email. Thank you.
https://www.zeusbtc.com/FAQ.asp
mostafaabbaspor 2022/5/3 18:19:35
Q:Hello Please send me the number of chips with the price
A:Dear customer, what type of chip do you need? I offer you a quote. We have contacted you by email, please feel free to contact us if you need it.
Matt 2022/5/2 22:51:36
Q:I am looking for a 14 pin ribbon cable for a Avalon 1246, is that an item you have?
A:Dear customer, we have contacted you by email. Or you can directly contact our FAQ place order, or contact our Pre-sale service via WhatsApp. Thank you.
https://www.zeusbtc.com/FAQ.asp
TRC20


COPY

ERC20


COPY

OMNI


COPY

Products

0
About products purchase, please contact our sales manager:
[email protected]

About miner repair and after-sale issues, please contact the repair manager email:
[email protected]

For business cooperation, please contact:
[email protected]

COMPLAINTS & SUGGESTIONS
If you have any dissatisfaction during the transaction or have valuable suggestions for us, please contact us via this email address:
[email protected]
Pay attention

Recently, some scammer falsely claimed to be an employee of our company.
For your safety, please check our right contact way: Here

CLOSE