| Unit Price: | $ 3.2 |
Why use L3+ U73 power buck module?
If the L3+ power chip is damaged or there is no voltage in the voltage domain, the L3+ U73 module can be used for replacement. The L3+ U73 power buck board can be used in the L3+ 10V step-down circuit control, on the hash board with no material, serious oxidation, and lack of material. The module has a total of 8 external solder joints, 4 solder joints do not need to be soldered with wires, and can be connected to 3 external wires (the PIC cannot adjust the voltage) or 4 external wires (the PIC can adjust the voltage).
1. GND: The negative pole of the power supply is grounded
2. 12V: 12V input
3. EN: Power on signal, connected to pin 3 of Q10
4. HG: Controlled by the upper MOS tube, connected to pin 4 of the upper MOS tube
5. LG: Controlled by the lower MOS tube, connected to pin 4 of the lower MOS tube
6. DAOUT: Connect to PIC, can accept PIC voltage regulation
7. FB(mos): Feedback input, connected to the large inductor L2, close to the MOS end
8. SW(out): Connect to the output terminal of the large inductance L2
Type: Step Down Board
Output voltage: 10.2V
Compatibility: Antminer L3+
Color: green
Material: PCB+Plastic+Metal
L3+ U73 module installation steps:
1. First remove the original IC U73, and use a multimeter to check whether the original 3 MOS tubes have any problems. The normal resistance of the large inductance L2 to ground is about 40 ohms.
2. Put the module on the inductor as above, connect the FB (mos) pad and the SW (out) pad to the inductor, and use an air gun and an electric soldering iron to dissipate heat.
3. Connect GND to the left side of capacitor C943, as shown above.
4. Connect 12V to the right side of capacitor C943, as shown above.
5. Connect the HG signal to the 4th pin of the MOS transistor Q5, as shown in the figure above, pay attention to check whether there is a short circuit.
6. Connect the LG signal to the 4th pin of the MOS transistor Q4, as shown in the figure above, pay attention to check whether there is a short circuit.
7. Connect the EN signal to pin 3 of Q10. If this pin is not connected, it is a forced power-on, which will cause the control board to fail to turn off the power supply of the hash board.
8. Remove the resistor R24, and connect the DAOUT signal to the position shown in the figure R24. If this signal is not connected, the PIC cannot adjust the voltage and can only work with a fixed voltage.
Related Products:
New L3+ 14V boost module without jump wire
MT3608 Adjustable DC-DC Boost Module 28V
Jay hỗ trợ nhiệt tình
Best quality product with best price, every order provided delivery with 7-8day thank you zeus mining.
Thanks, Jay! He responded to my feedback right away and helped me with the program. Thank you for everything
You guys are amazing, you have provided me instant solution of my problem. Thanks for your help and support
Jay always reply fast and with excellent service.
Excellent, polite, and well-mannered salesperson
Good bro, he solve a firmware problem whit a s21+hyd A lots thanks
Payment method:
How to determine product prices and shipping costs?When you are ready to buy one or more products. You can consult the sales Manager to get a sample of the proforma invoice. The category, product price, and freight are included. |
||
How to complete the payment?We have the following payment methods. You can tell our sales Manager which payment you prefer and complete it. After the customer service checks and confirms the payment is completed. Provide the proforma invoice. And we will prepare to ship. |
||
Cryptocurrency Payment |
||
 |
Bitcoin - The payment method at the designated address is efficient and practical and can be used anywhere in the world. Wallet Address |
|
 |
USDT - The payment method at the designated address is efficient and practical and can be used anywhere in the world. Wallet Address |
|
 |
ETH - The payment method at the designated address is efficient and practical and can be used anywhere in the world. Wallet Address |
|
 |
LTC - The payment method at the designated address is efficient and practical and can be used anywhere in the world. Wallet Address |
|
 |
USDC - The payment method at the designated address is efficient and practical and can be used anywhere in the world. Wallet Address |
|
Bank Transfer |
||
 |
Wire transfer - USD - YuanJi Card Number |
|
|
Wire transfer - USD, EUR, GBP, HKD, CNH, CAD, SGD, JPY, AUD, NZD Card Number |
|
|
JP MORGAN CHASE BANK, N.A. Card Number |
|
|
Wire transfer - USD - Zhou sicong Card Number |
|
 |
人民币支付 - CNY payment Card Number |
|
Other payment methods |
||
 |
||
|
Cooperation express: |
 |
Q: When will we ship after payment?
A: In order to ensure that the products we ship are in good condition. Issued approximately 1-2 days after receiving your payment.
Q: What if the product is damaged during transportation?
A: We will use a more robust package when shipping to avoid damage to the goods, and we can purchase transportation insurance in advance to reduce the loss of in the transport. although this problem is not common.
Q: What payment methods do we support?
A: We support bank transfer, wire transfer, BTC, third-party guarantee and Paypal.
Q: What should I do if there is a problem after receiving the products?
A: We have established good relationships with maintenance departments in many countries/regions in the world. For example, Venezuela, Iran, etc. If you have any questions within 3 days after receiving the goods, you can apply for after-sales service on the "My Order" page.
Q: Which express we support?
A: We will choose the cheapest and fastest transportation method for you. And we support DHL, UPS, TNT, Fedex, BRE, and also have express delivery services, such as Russia, the United States, Kuwait, etc.
China Mainland Hong Kong 
Business Hours: (GMT+8) 08:30-20:00 Mon to Sat 
Company Phone: +86-023-72227777
